I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi, I made a PCB board nrf51822.
Because of my mistake, Rx, Tx pin was not cross connected to MCU.
So i want to change Rx <-> Tx pin.
In the example of ble_app_uart_s130_pca10028...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
Hi, there~
I'm trying to make my own bootloader and starting with the secure bootloader sample code.
The problem is the orignal bootloader, that is compiled with secure...
Hello,
Recently I started working on BLE. I need details with respect to BLE 5.0.
Below are the features of BLE 5.0
2x Range (With 2Mbps PHY)
4x Speed (With...
Hi,
I've created 3 PWM pulses via:
Which works when I'm not starting Thread (from the examples/thread/freertos_coap_server example)
But when I start Thread...
Dear Sir,
I am working on the following scenario.
I have BLE device ( SDK 15 and softdevice s132). It is advertising for specific duration.
There are different phones...
Hi,
I am working on a project where I am sending and receiving Encrypted string data from my phone with nRF Toolbox to the nRF52840 DK. The basic paring is established along...
I recently got past an issue with not connecting to the LTE network getting an nrf_cloud_connect failed: 60 and had things working yesterday. I had support for that issue...
Hey, I'm trying to connect a touchscreen monitor (10 finger) usb into a computer, get a raw input report and send it over uart to bluetooth module and sent it to other computer...
In IAR it shows the cycle count registers and they appear to work as expected in that view (shown as CYCLECOUNTER) . In the IAR Project/SFRSetup it shows the address of DWT_CYCCNT...
Hello,
I am developing a simple HID device with output report to receive data from PC. I took keyboard example as base project and I want to increase output report size...
Hello!
I have a custom nRF52832 board with an FTDI usb/serial part running my app successfully.
I generally program the board with a JLINK and SWD, but I am working to...
Hi, I apologize for the question renewal, that is the same as ticket "SDK15 DFU and WatchDog issue" (for my mistake I closed the discussion post!). I have developed a custom...
SDK 15.3.0
I want to save some user data in UICR , this data will change when application runing. How to re-write the data into UICR.
I assume that the UICR will not be...
Dear sir,
I have merged the twi_sensor code in ble_app_uart code in order to read the temperature sensor MAX30205 with NRF52832 send it over Bluetooth. But I am getting...
