I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
DEVICE_MANAGER_MAX_BONDS is no more than 10.
That means that no more than 10 difference devices (smart phones) can switch the device to DFU mode?? (with boding).
Am I right...
Dear Nordic developer：
I am very eager to have the "Android-nRF-Connect" of the source code! I found the scan and DFU from the "Android-nRF-Toolbox" function, I also need...
Hi
I cannot find the minimum pulse length to trigger wakeup using DETECT from GPIO hw pin configured as SENSE pin in the data sheet for nRF51822.
Ex: set PIN_CNF[0].SENSE...
Hi,
I tried DEVICE_NAME with a AABBC Ddddff Tttttth Vs DEVICE_NAME as AABBC. The time taken to connect with a longer device name takes at least 3 attempts (in the sense,...
Dear Nordic Team,
Thanks for support.
I want to merge softdevice hex,application hex and bootloader hex. I am using windows 7 OS and my SDK version nRF5_SDK_11.0.0_89a8197...
When a nRF52 BLE as peripheral had connected to a BLE device as Central, if the nRF52 BLE also coule connect to other BLE device as Central at the same time with the supoort...
Dear Nordic Team,
Thanks for support.
I try to make zip file generation using command promt as per the nordic document(How to generate the INIT file for the DFU.pdf...
I want to test RF during production but I do not have any GPIO or UART points on my DUT so I don't want to run the DTM. Can anyone tell me what problems there are with this...
Hi:
I reference rate meter program：
“nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu”.
After function "device_manager_init"，I handle...
HI,
I am now trying to use nrf51_iot_sdk_0.8.0_f1f6187. And I have run example application in nrf51 iot sdk on nrf51-dk board. It works fine.
Now I want to develop on...
I want to send a service changed indicate after upgrading app by dfu.I know dfu already so that,but i don't know that how dfu do that.
there is service_change_indicate...
I used to able to get the blinky example in SDK11 to work. But for some unknown reason I couldn't scan my device using Nordic master control panel. The LED1 will be turned...
Can the nRF52 output the 32.768kHz clock on a GPIO. If so, do I need the 32.768kHz xtal, or can I output the generated clock from the 32MHz xtal? I need this clock to sync...
