Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...
Hi,
I trying to write an application with android for my nRF51822 device
I use Battery service example but every time i update battery level i need to request for changed...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,all.i want to run DTM on pca10028 develop board and connect it to my pc via USB (JLink CDC UART Port) on the board.My pc operation system is ubuntu10.4. what is the port...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,all. i run example.py(nAN34 document) on ubuntu10.4,then get an error:
./example.py:line 13:unexcept error near "(";
./example.py:line 13:'def main():'
what's wrong...
Hey there,
I am having issues downloading the SDK for the NRF52. It just goes to a blank part of the page. Is there a better way for me to get a hold of this SDK?
T...
So after reading some material it seems like I can pretty much define which pins are responsible for I2C communication. Is there any limitation to which pins I can set? Does...
Hello,
There are many anomalies in the NRF52 Revision Engineering A (QFAA-AA0, QFAA-AC0) .
This revision it is the current chip?
If so, do you know when there will...
I am trying to build the "Getting STarted" example app. I got it to work with Keil. Now trying Eclipse.
I got all the includes in the project set up and these all resolved...
I am working on getting the ble_app_hrs example from SDK 8.1 within Eclipse. There seems to be no association between the INC_PATHS in the Makefile with include files within...
