I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
Does the NRF IOT SDK have any support for the LWM2M application protocol or is there an implementation of LWM2M on the IPv6 Bluetooth Stack?
Imran
Hi All,
I want to implement a network which will consist of 64 sensors at different location sent to a central node . Can use the nrf51822 with ANT mesh protocol to implement...
I am trying to look at power consumption for very basic use cases to understand how often I need to go into SYSTEM OFF state. I have a development board and am measuring current...
Hi,
Is it possible to to switch between beacon mode and DFU mode (DfuTarg) without the need to press the button e.g.: by using DFU characteristic?
Is nRF51822 Beacon v1...
Hello Everyone!
I want to program nrf51822. I'm using open OCD 0.9. I created openocd.cfg file:
source [find interface/stlink-v2.cfg]
transport select hla_swd
set WORKAREASIZE...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I've downloaded S130 SoftDevice and found an example s130_demo_app which contains a project file for Keil v4, but when I am trying to open it in Keil V5 (that is the only...
Hello -
I'm not having any success using my PCA10024 as a dongle for MCP. Here is what I'm doing so far....
Remove PCA10024 jumper from P0.30-GND.
Connect PCA10024...
Greetings,
I am trying to minimize my BOM line items. Can C10 decoupling capacitor stated as 47nF/X5R on the reference design be replaced with 100nF/X5R without consequence...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi,
I modified the uart_example project for the pca10001 board of the nRF51822 evaluation kit to make it work with a UART TTL JPEG camera. So far, the camera can receive...
Hi,
There was a thread about using PAs (and not LNAs) with the nRF51 a while back with some good advice.
One question I still have: is there currently any way to support...
The nRF51 Series Reference Manual v3.0 notes the potential need to set the OVERRIDEx registers in the radio mode to values from FICR.BLE_1MBIT to meet deviation requirements...
hi, i am working on a project which needs a relatively accurate high frquency clock. when i ran my program without softdevice, the HF clock's accurency could fullfil our requirement...
