I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
nRF Connect SDK v2.0.0
VS Code 1.70.2
nRF9160 development kit
To view all possible log messages the fololwing logging configuration is set up in prj.conf:
CONFIG_LOG...
I'm using nrf52832, and it is connected with external mcu (stm32) to uart.
I'd like to connect this ble module to PC with ble (wireless connection), it was paired.
After...
Hello,
We developed a zigbee coordinator with nRF52840.
We discovered that our coordinator is not receiving the the beacon request coming from some Ember based sleepy...
Hi,
Is it possible to connect the Thingy53 over Bluetooth with Raspberry and store the sensor data in a database (e.g. Firestore).
I only found one solution, but its for...
Hi,
Is it possible to get the device name - i.e the GAP_DEVICE_NAME - of an unprovisioned or provisioned device using a serial device and the interactive_pyaci? It would...
Hi everyone,
at the moment we are trying to upgrade our nRF9160 software form the SDK v1.8.0 to the newer version SDK2.0.0. The main issue of the migration is our UART implementation...
Hi,
I'm using NCS v2 and VSCode on a custom board, and the android nrf connect app.
The board which has an external crystal, which I am not trying to use, in favor of...
Hi,
I am migrating to use Advertising Sets, which require Extended Advertising, and I am seeing that the number of connections per-connectable-service is seemingly reduced...
Hi,
I have been successfully working with CoAP customized client/sever app for a custom dev board. This custom dev board was based on Minew MS88SF21 module. I have created...
Hi,
I create two extended adverts, one connectable and one none, (nRF Connect 2.0.0) using the following code:
This works great, but then i want to amend the data...
Hi, I have just started looking at integrating Matter in my devices and am looking to measure voltage. However, there is no cluster under the matter clusters that matches...
Hi,
There is a loose wire on our PDK, The right side is on the cap, but the left side is loose and not clear where it came from. Can you help?
Regards,
Peter
Hello everyone,
In my application, and in samples I have studied, the A-GPS data request starts with the NRF_MODEM_GNSS_EVT_AGPS_REQ event when the modem wakes up/is started...
