I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I am creating a Matter accessory device with the nrf52840dk and the guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
Is it possible to build an asset tracker on the nRF91 without the use of LTE-M or NB-IoT? If there is a solution, could someone please advise. I read something about GNSS...
Hello,
SDK : nRF5_SDK_17.1.0_ddde560
Example: ble_app_uart
I want to use custom peripheral and disable BSP.
but when comment buttons_leds_init(&erase_bonds);
I...
I'm using nRF Connect SDK with nRF52840dk and going through the UART samples and currently have both the P olling and Async methods working to some extent. But questions for...
Triggering advertising by button pressed. But when advertising state is not idle. Both sd_ble_gap_adv_set_configure() and ble_advertising_start() failed with errCode 0x8....
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I am using a function in my source code that reads the current RSSI of the connection. The function, read_conn_rssi...
Hi there,
I am trying to implement the OTA DFU feature via Zigbee in my product. i tried to implement the example available in SDK as below https://infocenter.nordicsemi...
We are able to build nrf5340_audio application with SBC codec,
but error occurs when program the app core with buildprog.py
dongtaotao@dongtaotao-OptiPlex-5070:~/ncs_v2...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Greetings,
In our product, we encountered an issue when data saved in flash (FDS) that were previously retained are erased during DFU on some devices . This was indeed fixed...
Hi, I'm building an applicaiton based on ble_app_uart. I got that using idle_state_handle(); function to set the my nRF52833 into system ON mode. I disable system OFF mode...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
