I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hi,
My nrf52840 is not detecting the USB, i tried by pressing the SW5 after that bootloader led starts blinking but not showing any drive in the PC also
can you please...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I have an applications that was using NCS 1.7.1 in its west manifest. I am going through the process of upgrading to 1.9.1
My application using zero latency IRQs and sets...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
I am trying to interface the Grove 4 Digit Display(TM1637) with the nRF52840 DK.I have successfully interfaced it with ESP32 and get clear output after researching for the...
The main loop in our nRF9160 (NCS v1.8.0) is a typical main loop with semaphore following https://docs.zephyrproject.org/latest/kernel/services/threads/system_threads.html...
Hi
I attempted to create a 32.768 kHz signal from the nRF52840. When I use the HF external clock: NRF_CLOCK->TASKS_HFCLKSTART = 1 ; the generated clock signal looks great...
Hello,
I am waking nRF52805 up from SYSOFF by an accelerometer, after which I want to wait for a second and then start advertising for a short period.
All is working fine...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Is there a limitation for number of INT's If is how do I attach same interrupt on multiple buttons
for(..my buttons){ ...
ret = gpio_pin_interrupt_configure_dt(pb, GPIO_INT_EDGE_TO_ACTIVE...
I want to change the connection params in peripheral role with nrf52840 without informing the central device to do the actual setting operation, yet I don't find a relevant...
I'm trying to implement the WS2812 driver in my own project. I'm referencing the sample code stored in zephyr/samples/drivers/led_ws2812. I have copied over all of the correct...
In the scanner activity of the Blinky android app, there is the following import:
import com.switchmaterials.android.nordicble.databinding.ActivityScannerBinding ;
It...
Hi,
My Thingy91 has suddenly stopped connecting to the mobile network. It came with an ibasis SIM which has data, but since this morning I am getting an ESM 38 + EMM 19...
