I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hello,
I'm testing periodic advertising sample (sample/bluetooth/periodic_adv,with no changes to the code) on nRF Connect SDK 1.7.0, on BBC MICORBIT V2 that has a nRF52833...
Hi,
nRF Connect SDK 1.7.1, windows 10 X64
run SEGGER Embedded Studio.cmd or click segger_embedded_studio IDE menu File->Open nRF Connect SDK Project,
it will be got...
I have impulses coming to a GPIO input. Each pulse (say: rising edge) should toggle some other's GPIO output. What I know, is that I cat apply a task to a GPIO output. This...
I am using nrf52832 board sdk vr 17 s132 soft device. I want to have a way by which i can reduce the brightness of led while it blinks during advertising mode using PWM. pls...
Setup mcuboot and dfu to upgrade firmware on the nRF52840 of our board. Upgrading to new firmware works as expected and the new firmware is running after the install. If I...
Hi，
I am using nrf52832+freertos to develop a low-power product based on the example(ble_app_hrs_freertos) in the SDK, but now I find that the power consumption far exceeds...
Hello Nordic! I have connected a sensor to the DK via SPI. It outputs a lot of data, a lot... for 1 second of data I get 4096 entries. Each entry is 10 bytes in length.
...
I'm working on a design featuring two different MCUs. I'm looking to use the nRF52840 as one of them. I need both processors to be able to send each other messages and ideally...
Hi,
I have a weird problem. My application starts two timers, one after another. Like this:
Normally it just works - no errors, nothing. However, after a DFU OTA upgrade...
What is the best method to store TLS certificates on the nRF5340? I have seen 2 options, but I'm not sure what is best practice and what does work.
If I store the certificate...
Hi,
i just got my hands on Thingy 52, just want to know how do i get started in retrieving data from it, specifically for motion(accelerometer data), if someone can point...
Hi,
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple of weeks, explored almost the whole devzone, learned a...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
HI,
I need to check the following thing with you. I need to use an I2S mic with NRF5340 between the mic and the controller we need to place 2meters of wire. So, I need...
