I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I accidentally clicked on verify answer, is there a way to undo this?
It would be very nice if someone could still have a look at my problem, thanks.
https://devzone...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the SEGGER...
Hi All
I am now working in Channel Selection Algorithm (CSA), Bluetooth Low Energy. Basically, I would like to test both CSA 1 & 2, and also I would like to modify the CSA...
Setup:
SEGGER Embedded Studio for ARM (nordic Edition V4.18 (64 bit)
GCC
Windows 7 Professional
SDK: nRF5_SDK_15.3.0_59ac345
Issue:
In order to use the GPIO...
Eagle pcb and schematic reference designs on github are incorrect.
Reference nRF52840 pcb schematics and layouts are exactly the same for examples 2-6. I believe each is...
Hello,
I am using a nRF52840-DK with an HX711 in SES. I have been utilizing the code provided by Vidar Berg that can be seen here .
I downloaded the zip file, unzipped...
I'm developing the PCB schematic for a system using a nRF52 module that I found that suits my needs SKB369
At the same time I'm implementing a JTAG connector to flash my...
I was wondering: if the last sample of a buffer in the SAADC (using easyDMA and scan mode) is outside the limits, which interrupt would come first, the END or the LIMIT interrupt...
Hi, I am getting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event since I increased the size of MAX MTU to 203 from 23. At first, I received INVALID PARAM error and then found out...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
