I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hello dear Nordic Developer and Hobbyists,
first of all I would like to thank the developer team for the nice mesh demo. It functioned well and explicates the concepts of...
Hi,
I am not getting any response from the previous ticket. Did it get accidentally closed?
Case ID: 225033
Can please someone look at it? We are in urgent need...
Hi, I have tried to run nfc example, but it doesn't working, accidentaly i have found out that if supply 3V nfc not working, but if supply 2.7V and less it works, what is...
Hi, I'm designing based on the Altium files, but I'm not an antenna expert so I would like to know if you have any antenna recommendation for a low profile, because the one...
Hi,
I'm working on nrf52832 NUS. When i connect to device with "nrf connect app" i can see the data coming from sensor. But few seconds later device disconnect.
When...
Hello
I have 3 nodes, 2 Thread CoAP servers and 1 BLE/Thread Coap client.
Let's call them THnode1, THnode2 and BLE_THnode0.
I do not know the IP addresses of any node...
Hi,
I use "printf" or "app_uart_put" function to print message to UART., how can I check "all of the data had been transmit out complete"?
Thank you,
Chianglin
Hi, I want to test sending multiple packets of data with each packet having the maximum possible size of 247 bytes. I am currently testing with nRF Connect app. When i try...
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac.
Example nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\cli\uart\pca10056.
define BOARD_PCA10059.
...
I am using nrf51822. Separately BLE and flash are working perfectly alright. But when I comment err_code = ble_advertising_start(BLE_ADV_MODE_FAST); this line flash is working...
Hello,
As per my understanding, SPP was supported by BT Classic and no more supported in BLE. I have a device, which runs SPP. It has to be connected to the BLE client....
Hi, I am now developing a product which uses nrf51422 chip. In this product, I use buttons to turn on and off (since I don't have hard-power cut off circuit, we use system...
Hi
I wonder if the SDK DTM example can be used with a Rhode & Schwarz CMW500 unit. Are the commands compatible with each other, i.e. expected by the CMW500 and DTM example...
Hi,
we're evaluating NRF52 as a platform for a project in the agricultural space and I have some beginner's questions:
Is it feasible to use a timer firing at 100kHz...
Hello,
I created a custom board with the BMD350 module (it has a nRF52832 chip), and I a trying to program it with the BMD300 eval board.
The module on my custom board...
