Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi
Can anyone please explain me as how to change the start address of flash (while using soft device) and changing the start address of RAM too. I am working on nRF52840...
I'm looking at the patched version resulting from applying the pc-ble-driver patch, but this might be present in the original as well.
675 case APP_USBD_CDC_ACM_USER_EVT_RX_DONE...
Hello,
I'm trying to receive a 2-byte data from a sensor from Maxim Integrated MAX31875 but the nrf_drv_twi_rx function only receive 8 bits data. Does this function to receive...
I'm evaluating the NRF9160 DK, and have run into some interesting issues.
I find that the AT client works, sort of, though it's quite flaky and I quite often get timed out...
So, time to give back...
Updating this post ( https://devzone.nordicsemi.com/f/nordic-q-a/23488/a-nrf52-function-mapping-to-nrf51/124863?focus=true#92262 ) which outlines...
Hello
I am in a process of pre-manufacturing for NRF52832 and have a fully working application containing
softdevice: s132_nrf52_6.1.0
secure ble bootloader
application...
As i understood by reading the forum and documents, the maximum advertisement packet length is 31 bytes. That means that devices with custom UUIDs (128bit = 16bytes) may not...
Hi,
I am a hardware designer. I have little knowledge about firmware or software.
Now I want to apply the nRF52832 to an ultra-low power application as a beacon.
I...
I have recently ported my nRF52832 application from SDK 12.3 to SDK 14.2 and have been disappointed to find that the preripheral is locking up after a period in operation...
Hi,
My product have to pass SRRC certification,but the pre-test is fail. The certification lab need to test RF frequency at 2402MHz, 2441MHz and 2480MHz separately,and the...
I have a nRF9160 DK that I am trying to get on a network. The iBasis sim does not appear to be in the coverage area, the SIM activated, but has not had both LEDs 3 & 4 blinking...
Hi,
I have nRF9160-SICA Modules with me and I designed a custom board for them. I do not have the nRF9160 DK.
I want to know if there is any way to program nRF9160 using...
I have two TIMER instances, TIMER1 and TIMER2, both setup to Clear Mask on timeout (aka restart). I use TIMER1 and PPI to trigger ADC measurements every 5msec. In the ADC...
I've been documenting this issue and asking questions here:
Intermittent device reset in modified ble_app_beacon example
Since I need to post a proprietary schematic,...
Hello,
I was examining the power supply part of the Thingy and I noticed that the charging current is set to 0.5 C, wich is 720 mA (checking XR6804's datasheet it seems...
