Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
fds appears twice in ble_ots:
1. In ble_ots_init:
err_code = fds_init();
2. on_disconnect
err_code = fds_gc();
It does not look like fds is really used in ble_o...
Hello!
I use Segger Embedded Studio. Ubuntu 18.04 I'm trying to build mqtt_publisher project from zephyr samples. And get error: undefined reference to `sys_rand32_get'...
Greetings,
Here are the details:
IDE = SES v4.12
SDK = v15.2.0 and v15.3.0
Hardware = Nordic nRF52 DK (PCA10040 v1.1.1) * 2 and Rigado BMD-300-EVAL * 2 (vB)
I connected...
Can you explain me what I need to do in order to have the esim ? Do I need a physical component ? I am new to this subject if someone can help me a little bit. Thanks
I am trying to measure and characterize expected battery lifetime of my design. I've noticed that as the effective Connection Interval goes up, so does the Rx current peak...
After init I2C channel
#define TWI_INSTANCE_ID 1 // because SPI0 share same reg add with TWI0 we change and enable TWI1
#define MAX_PENDING_TRANSACTIONS 5
NRF_TWI_MNGR_DEF...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
