Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi. I have built an ble application which runs on the nrf52832 with softdevice S132 V 6.0.0. In addition to the application and the softdevice I program a bootloader on the...
Hello,
I am learning bluetooth mesh with Light switch demo example. I have downloaded the folder "nRF5-SDK-for-Mesh-master" from the link "https://github.com/NordicSemiconductor...
Hello all!
We have custom HID with multitouch BLE device. We took HID descriptor from USB where this works pretty good, ported it to BLE and it seems not working as expected...
I just upgraded to nRF Sniffer V2.0
The Time column of Wireshark shows wrong values for short delta times. Is is set to "seconds to previous packet"
My advertiser runs...
Dears,
I have a problem with the ble_ant_app_hrm in the examples (multiprotocol). I am using a pca10040 demo board with sdk 14.2 with IDE SES on a MacOS
I have flash...
Hi, I'm using nRF52832 with SDK 15.2 and 3.0 (Mesh). when I try to provision 2 or 3 client/servers the nRF Mesh application behaving properly which means provisioning is happening...
Hello,
I would like to use an usb dongle with nRF52840 above and
- on bluetooth side give an spp or vsp profile
- on usb side be an usb cdc device
the reason is: I...
Hi,
We are currently implementing a mesh application that is expected to have a large number of mesh devices. We have already tested DFU on a smaller mesh and it is working...
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. switch sequnce activated with LED 3 and 4 starts blinking. After that LED4 starts blinking...
Hi,
During provisioning of a device the Device Name is changed to the default "nRF5x" after completion of the PB-GATT connection. The name is later on changed back when...
Hi,
I am trying to use latest pc-ble-driver. The code is based on pc-ble-driver-js. When I call sd_ble_gap_scan_start(), I get only one "device discovered" event. This happens...
Hi, I need to use nrf52832 as HID keyboard and send function keys F1-F9 to computer. I have tired to run HID keyboard example in nrf5 SDK. How do I send function keys instead...
Hi,
I tried to build the Connect SDK documentation according to the guide: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/doc_build.html
I did this on...
APP_TIMER_CONFIG_USE_SCHEDULER affects how are handled. One example is the timer call back is actually called at interrupt level if APP_TIMER_CONFIG_USE_SCHEDULER is zero...
