Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello, I am currently working on a nr52840 s140 Sdk 15.0 card and I want to recover data from a component running on the i²c bus. (I have not yet installed the component on...
Hello,
I would like to know if it is possible to use a nRF52840 as bridge between ethernet and 802.15.4/thread. For a sensor network I need an ip connection between multiple...
Hi,
I'm using nRF52 DK. I was checking the message sent by NRF_LOG_INFO() on Termite. I'm getting driver error when I try to connect to laptop's bluetooth.
Without the...
Hello
what is the maximum limit for PWM outputs pins on nrf52832? Can we use all the GPIO pins as a PWM output?
For ADC, i can see there are 8 dedicated pins , but i...
hello i am beginner in this,i am using example\ peripherals\ saadc for nrf 52832. This example code is done by using timer and i could not understand how to use timer. We...
hi all ,
i now need porting nrf_libuarte_async lib for my project . it show some error
How to deal with this problem？
i reference (experimental_libuarte project...
Hi everyone;
I wanna send to data my uC from my phone. I looked peripheral uart example. This example use only send data phone from nrf52 SoC. What can i do? How I add...
Hi All
I have developed some code by modifying the 'ble_app_multiperipheral_pca10056_s140'. I have tested my code on the NRF52840 DK board (PCA10056) and everything seems...
Hello
I have developed an application for the smart beacon and I have the following problem:
I use two diferent sets of values for the connection parameters in order to...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
We are developing a BLE Mesh product and we use the mobile phone mesh library iOS and Android for the node provisioning.
The final user will need to synchronize more than...
Hello,
We have a Buttonless custom board based on a nRF5282 with SDK 15.0.0
The DFU OTA Buttonless works fine, but to prevent the device to brick we put a physical button...
Hi all,
I am having build error of example light_switch_dimming_server in mesh sdk 2.2 that timer 2_irqhandler multiple define it is define in
D:/../../nrf5_SDK_for_Mesh_v2...
Hi.
I'm struggling with BLE example projects on the my custom board.
my board uses nRF52832-QFAA, 16MHz external crystal with no 32,768kHz optional RTC.
and I choose...
There appears to be a conflict between ble_advertising and broadcasting while connected. If connected, the ble_advertising state machine still gets TIMEOUT messages from the...
