When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
Hello All
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve...
In SDK13, the initialisation of the low frequency clock used to be done within sd_softdevice_enable . In the SDK14 version of nrf_dfu.c , the LF-clock is already initialized...
Hi, I want to use the AES-CCM of nRF52832. But it can not work with the softdivice. I have read the following question and answer.
https://devzone.nordicsemi.com/question...
Hello All,
I have a peripheral device where one service with 4 characteristics is implemented.
Out of these 4 in 3 services notify is enabled.
Now I want to subscribe...
I have a situation in which a central device (A) must be able to receive from a power constrained peripheral (B) with very low latency, but likely at long intervals.
To...
Dear Nordic,
I tried to download the new SDK nRF5-SDK-for-Thread from here:
www.nordicsemi.com/.../60504
However, when I clicked on it I only got the TTM 0.11.0.
...
Hi every one ,
I am using NRF51822. I download the code
from this link. github.com/.../nrf51-ble-tutorial-advertising
I able to flash the hex file & see board are...
hi~
i am working with nrf 51822 with custom board and softdevice s110.
i am using is7020-a20 temperature / humidity sensor via twi (i2c)
i tried 2 versions of twi example...
I followed this guide , I'v managed to run make files and flash them using the terminal, then when trying to build the project in Eclipse, I get this :
Make: no rule...
Hi,
I am following the "Bluetooth low energy Services, a beginner's tutorial", however, this tutorial is written for SDK V11.0.0 and I am using SDK14.1.0, softdevice 5...
Hi there!
I've followed the guide to Eclipse GCC (using OSX) from here: devzone.nordicsemi.com/.../
I had to add some stuff to main.c to have it built (e.g. BSP_LED_APP_TIMERS_NUMBER...
Hi, I'm having an issue with some PCBs I've designed with the NRF52832 on a module. When I first connect the board through a j-link, the device is not detected in NRFgo studio...
Hi,
I wonder CRITICAL_REGION_EXIT() in app_sched_event_put() have to be moved to the end of function.
CRITICAL_REGION_EXIT() is called after proceeding index in current...
Hi everyone,
I am trying to port freertos on the nRF52832, but it is blocked in the vPortSuppressTicksAndSleep function. Below is the code for configuring the system and...
