Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am using the mbed compiler.
When I produce code using the "App with Bootloader" option, I can do FOTA updates and my code runs fine, as long as I don't enable the ble uart...
Hello together,
we are running the DTM in different modes to check the module (nrf52832, sdk 5 version 11). The carrier test gives us a current consumption that meets the...
Hi
I try to program Insight ISP 130301 with a hex file, which works on nrf51 PCA10028. Unfortunately, it doesn't work. I try to loop for each pins and set it's state, and...
I'm trying cominicar me through Termite between the application plate (nRF51-Dk kit) and a device that supports BLE, but the connection between PC and the kit application...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Hi again, I posted earlier in another post that my writeCharacteristic is responding with status 6.
Details:
Android version: 5.1
Nordic device: nRf51822 S110
I have...
Hi
I want to use nrf52 LATCH register.
I can see the correct bit set in the register, but I am unable to clear this bit.
I have tried NRF_P0->LATCH =0xFFFFFFFF; for my...
Hello
I am doing a PCB design using nRF51422-QFAC chip. I did based on nRF51-DK but now I would like to change for a SMD antenna (2450AT18A100 from Johanson Tech.) instead...
Hi ,
I am working on one application in which i need to stream the ADC values over BLE to the mobile App. This should happen at very high rate i.e. 1000 samples per seconds...
Hello,
I'm trying to do something like ibeacon where data is pushed to any device listening, but I want to update the advertising data from raspberry pi 3 since it supports...
Hello,
I am working on an application where the nRF51 acts as both central and peripheral. The device is in permanent connection as peripheral while scanning for other devices...
Hi
can ESB be considered RealTime transfer as soon as it has it's timeslot?
Outline of use-case:
Device advertises existenace on BLE
If there is data waiting...
I am trying to implement a REQ line protocol over GPIO to signal to the Master when it is ok to receive data. Basically, I want to pull the REQ line high when the nrf51 has...
Hello,
Ble spec says that "new alert" characteristic - field: "category ID" can have 1 or 2 bytes.
here
But it seems in your struct you let it have only 1B.
typedef...
