Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I'm newbie in the RF Design. For my project nRF52832 chip is being used for BLE and NFC. Have a query regarding the NFC section which is listed below-
Please refer...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? For example, I can use the...
Hi Nordic Developer Zone,
I also encounter a problem with enabling indications in my Android project. I want to enable Indications so I can gather informations store in...
Is anyone able to access the documentation for the Advertising Module?
Try this:
Go to the InfoCenter at:
infocenter.nordicsemi.com/index.jsp
Select the following...
Has anyone tried to plug an R3 shield to the nrf52 DK?
I was about to try, but it looks like the pins don't line up correctly - but then I have no experience with R3 shields...
Hello everyone,
I'm using the nRF52832, i would like to shutdown the timers, so i can enter the low power mode. In the datasheet tasks_shutdown for the timer modules is...
I have an application which receives commands from a co-processor via UART. Some commands are BLE-related such as, e.g. start-scan, stop-scan, connect, etc.
As the UART...
In nrf_drv_adc.c , there are loads of these ASSERT() macro calls:
ASSERT(mp_state == NRF_DRV_STATE_INITIALIZED);
But there is no variable mp_state. This will fail...
Hi! I have asked a question in this topic ( devzone.nordicsemi.com/.../) and now I can send one packet of 20bytes. What I cannot do is sending two packets at the same time...
I have nRF51 Dongle.
I can set it in BOOTLOADER mode and update firmware like:
developer.mbed.org/.../
I see the dongle in Device Manager/Disk drivers like "MBED microcontroller...
Hi all,
i have a little issue.
If i remove the bond information with app Master control panel, my slave cannot connect again with my phone. [Pairing Reject from Nordic_CTS...
I am moving from S110 and SDK 6 point something to S130 and SDK 10. I have my basic BLE code going but am unable to get the SPI back-in-action. I am using gcc and the s130...
I use NRF51822qfaa,s110 v8.0, now I use master TWI to drive the TWI bus chip.
the TWI bus chip Slave Address is 0x48.please see the below program .
question:
1.The...
this is the main program!
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards.h"
const uint8_t leds_list[LEDS_NUMBER...
