Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
What is the recommended PCB thickness of the nRF51822-QFAA Reference Layout? It'd be great to have a specification in the package including the full spec of the PCB material...
Hello Folks, I'm starting some work with the nRF51822 Evaluation Kit (PCA10001), but have very quickly run into a blocker when trying one of the ble samples. (I've previously...
With Soft Device 5.1.0 I generated the binaries from the hex by doing:
arm-none-eabi-objcopy -Iihex -Obinary --remove-section .sec1 --remove-section .sec2 s110_nrf51822_5...
Dear support,
We are in the design stage for a BLE application. We looked at different options. Although the NRF51822 seems better in specs. The TI parts CCxx offer this...
So far I have made a successful program that utilizes BLE to send and receive radio signals in Kiel. But I have only been testing this program by using the provided Master...
I just entered a Case to Nordic with this same question but do not expect to get a response over the weekend so I am posting here. I made the assumption that the Nordic Cases...
Dear everyone:
Now,I have a project which use Nordic product solution to developemnt.
And , We need your company to provide some information and solution.
(like,have...
What is the maximum value of RSSI parameter for nrf_gzll_device_tx_info_t structure?
I have done a test on RSSI parameter value return in nrf_gzll_device_tx_success callback...
Hi Nordic
I don't fully understand the drive settings for the GPIO. For example S0H1 means when the pin is CLEARED, it will use standard drive (can sink 0.5mA) and when...
Hi there,
i was trying to implement a firmware for a small device using the nRF8001 only in broadcasting mode.
So far, everything works fine. But one thing mentioned...
I'm happy with the status of my app on the evaluation board and I'm ready to start downloading it to my target board. I plugged the Segger J-Link Lite CortexM board into one...
