I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
Hello, I can commission bulb and switch pass, then I refer this link( acl and bind ) to write ACL and binding both, eventually I can use switch to control bulb!
But I have...
Hello,
I have a firmware that sends every 15 min a packet to nRFCloud using nrf_cloud_coap_json_message_send().
The code is working great most of the time : hundreds of...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
We aim to use an external Cellular module for MQTT communication.
I found that the nrfxlib/nrf_modem library is only supported for nRF9x series MCUs. Does this support...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
We want to evaluate the Bluetooth: nRF Distance Measurement with Bluetooth LE discovery functionality. But we only have nRF5340 Audio DKs. Not ordinary nRF5340 DKs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with two specific exercises: l2_e3 and l4_e1 . Other...
Hi,
We have enabled the watchdog feature in our application running on the nRF5340 and nRF7002. In rare cases, we’ve observed that the nRF5340 hangs during zephyr library...
