the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
hi dev
I have a question about nrf52 dk board.
I have 2 dk board : one was written 2021.06 and the other one was written 2022.12
anyway, when I debug same file which...
We have a custom nRF9160 board which in Zephyr v1.7.1 defined in the boards\arm tree. It is a near copy of the nrf9160dk_nrf9160 folder with hardware changes and additions...
Hi Everyone,
I am using NRF52840 in my project and compiling my code using sdk 17.0.2. My application requires 7 interrupt pins to be enabled. However when I am enabling...
I have nrf9160 custom board, and I have issue with SIM module. I'm not getting 1.8 volt in "SIM_1V8" pin.
- I download the latest version from nRF Connect SDK v2.2.0 from...
Hello,
I am trying to setup a device ( Semtech LR1110 ) connected to SPI 1 peripheral on the nRF5340pdk .
I have a driver code for it. My question is this.
How can...
Hi,
Happy New Year!
I have been going over LwM2M location assistance documentation , and cannot figure out whether LwM2M library handles the response automatically, or...
I'm using Asset Tracker V2
with the Settings Enabled and tsetting up an external littlefs storage area.
I want to use the shell built in command "fs" to write stuff to...
I have two i2c modules on the same bus and I plan to have a common timer for both of these. one of these is a sensor and I only want to read the sensor values at a predefined...
Hi I am using the Zephyr code base after trying to update the ncs to 2.1.2 from 1.9.2 I notice that the function "flash_area_open" is returning a -2 error as it couldn't find...
Hi,
I am using nrf mesh sdk v5.0.0 and am using sensor server model example to build our own application on top of it. SOC we are using is nRF52832. I have enabled the...
Hi,
I have few doubts regarding the internal flash of nRF52810. I am not using SoftDevice. I am using SDK 17.1.0
I would like to write around 20 bytes to internal flash...
board : nrf5340 sdk : nrf-connect v2.1.2
Hi. I am studying OpenAmp and RPMSG using NRF5340DK board.
I looked at the examples below for studing OpenAmp and RPMSG.
C...
nRF Connect SDK 2.2.0 on Windows 10 pro, I have a nrf52840-DK and a nrf9160-DK. I would like to test a simple OpenThread CLI application
I have the following prj.conf
...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
