Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
HI
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_prod_config_generate_hexfiles.html
Referring to the information on the website...
I seemed to be randomly causing problems to our nRF52840 Zephyr v2.02 sensor's flash.
Previously I had bricked 3 sensors somehow. Before full production, I need to know...
Hello,
I want to implement a vendor-specific service on the nRF5340.
Is there any suitable sample code in NCS 2.2.0?
Or if there is any documentation I should refer...
Hi,
I have a nrf52820 on a pcb without 32Mhz crystal. I am using nrf52833DK to flash the nrf52820 on the pcb using debug out port on DK. I am able to see the connected device...
Hi, it's me, once again. Thankfully the last problem I had was actually my fault... I got distracted and didn't notice a small implementation detail... anyway... Here's today...
Hi,
The customer test routine serial_lte_modem mqtt returns 9,0
What does this state mean?
* ``9`` - Ping response from the MQTT broker.
Thank you for all your...
Hi,
I'm getting the following error during migration from 2.0.0 to 2.1.0:
[505/551] Building CXX object CMakeFiles/app.dir/C_/ncs/v2.1.0/modules/lib/matter/src/app/util...
Hi all.
I'm trying to learn a bit more about the device overlays,
I'd like to know how I would access the "gpio-line-names" that I've specified in my overlay in my application...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
Hello,
I am currently having my product, which is based on the nrf52810 SOC, tested and certified. I have been told to set my device up to use the DTM firmware example in...
Hello everyone
I have a few questions about how the nrf chip works: - does nrf52 work by sending AT comman and we need an intermediate chip like pca10040 send AT command...
I am trying to modify the Zigbee light switch example to transmit commands to the first bound endpoint, rather than to a bulb address determined by the app logic:
ZB_ZCL_ON_OFF_SEND_REQ...
Hi,
I am testing GPIOTE interrupts on 833, and noticed the interrupt is not fired sometimes (randomly) on power up. The input level did change as measured but the interrupt...
In this commit https://github.com/nrfconnect/sdk-zephyr/commit/d4023b3c1b8c32d978299143125ce5543c9bc6bb and this conflicting commit https://github.com/nrfconnect/sdk-zephyr...
