Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi Nordic!
I'm a fan of your products and usually work in Segger Embedded Studio (used it with nRF Connect SDK v1.9.1).
In that application you can create a "blank"...
Hi,
1. I would like to know which rexample should be used when using nRF52820 as master and slave?
2. How many slave can be connected at most?
Thank you for all your...
Hi, Working with nRF5340 in NCS 1.9.2, I've overridden weak usb_update_sn_string_descriptor function to set iSerialNumber at runtime. I wanted to read the actual serial number...
Hi, I am currently working on moving our app over to PSM mode.
We have earlier used manually disabling and reenabling the modem when sleeping, using LTE and getting GPS...
hi, I am trying to use Hal_Atomic_Start() and Hal_Atomic_Stop() to imply an atomic block, in order to avoid interrupt from system when execute the atomic block, source code...
Hi,
The nRF UART running over the ASYNC interface consumes a lot of current even when not in use. As ours is a battery-operated device we intended to disable UART when not...
hi
im working with a custom project which can flash easily on a eval board im trying to add dfu for my project but it didnt work hence i added my project into the buttonless...
Background:
In pursuing development of Thread-enabled devices for use in home automation, especially using the just announced Matter 1.0 protocol, the nRF52840 Dongle is...
Hello,
in my device tree there are three nodes/items concerning battery Management:
One load enable pin
One measure enable pin
the required ADC configuration
...
Hi Team,
We are currently using nrf Connect SDK 1.8.0 and developing our application using nrf52833.
Currently we use our own git to maintain our application and nRF...
Hello, When enabling the Sensor system and having a qdec device enabled in my dts I get the following error:
This seems to be a bug with the Zephyr code checking a const...
Hi,I'm using nrf52832. I configured P0.20 as GPIO output,P0.22 as GPIO input.These two pins are connected wiht a 10Kohm resistor.I measured the voltage level on P0.22 is about...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example.
I'm following this guide https://infocenter.nordicsemi.com/index...
Hi,
I am working on thingy91, I have created/added a BMS module in the project which gives different values for different data fields.
Everything is fine as BMS is transmitting...
Hi,
I am using TWI channel0 on my nRF52833 as master to get readings from a few sensors.
I need my nRF52833 to communicate with another microcontroller over TWI/I2C so...
