Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hello,
I am using NRF52833 with Soft Device S140, SDK 7.2.0.
according to sd_ble_gap_tx_power_set() API
"* @note Supported tx_power values: -40dBm, -20dBm, -16dBm, ...
Hi,
Out of testing large number of boards, observed one board is not working. When tried to debug, found this weird problem. Code is stuck in LFCLK init part.
main() ...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now my customer has this issue: - End Node connected via...
app_button_init() and app_button_enable() returns NRF_SUCCESS. But event handler of app_button isn't called.
log messages of nRF52832 device is as follows.
00> <debug...
Hello,
Somehow my thingy91 is no longer working so I decided to flash it from the beginning.
I put it in MCUboot mode ( holding SW4 and turning on the device)
in Programmer...
Hi, I'm new to the NRF Connect SDK, as well as nRF Connect for Desktop.
I have a nRF52840 Dongle and a nRF52840DK.
The nRF52840DK worked well. But I could not program...
Hi Team,
Currently, we are working with NRF52840.
We have developed an android app to communicate with NRF52840 which has the functionality of an automatic connection...
Hello all,
I am porting the code from the nrf52dk to the nrf52820 based module and so far so good!
However, I can blink the LED on certain pins while not on the others...
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I have implemented a service to display RSSI. I have setup the service according to the instructions provided by Nordic...
Hello everyone, I have an oxygen sensor"Gasboard-7500H" i need to read purity and flow with UART communication, this sensor works perfectly with Arduino and display corrects...
Hi,
I am developing an embedded system that uses Bluetooth communication and would like to manipulate certain Bluetooth characteristics such as TX power and RX sensitivity...
BLE Device
- nRF Connect SDK: v2.0.0
https://github.com/NordicSemiconductor/IOS-DFU-Library
This library doesn't seem to support the new nRF Connect SDK.
Which library...
Until 1.9.0 of NCS, SES was recommended, so it was possible to use OpenOCD from there. With NCS 2.x.x, VCS is recommended, so it's good to use it, but I want to continue using...
Hi,
We have some variables in shared memory. These variables can be accessed directly by both cores, and this is not controlled through IPC.These variables can be accessed...
Hi Nordic Team
Starting Point:
Provisioning of dimming server is done with code from the PB Remote provisioner, working so far.
Publish of model to group is acived similar...
