Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi, We have custom board files (copied from 5340dk dts files) and I wish to remove all redundant DK stuff from my DTS and free up pins. Can I remove UART0 from both the app...
I have gone through the Nordic Academy to install the tools and build the first example which is blinky. I am using MS Visual Code and SDK version 1.9.1. I have seen some...
Hi,
I use serial port example to do out UART exchange data function. But I get a problem, I don't know why? Below is my source code.
When I send 2 bytes data to...
Hi,
I am trying to enable UARTE0 on BMD-330 module. The serial config looks like this
# # Capabilities # CONFIG_SERIAL_HAS_DRIVER=y CONFIG_SERIAL_SUPPORT_ASYNC=y CONFIG_SERIAL_SUPPORT_INTERRUPT...
Hi,
I tried porting LC3 to my own 5340 project with reference to the SDK(nrf5340_audio_nrf5340_audio_dk_0.4.0), but I had a restart problem when initializing LC3
sw_codec_lc3_init...
Hi, I have a mature product that is programmed with a J-Link compact, I have 4 different PCs to program and a custom UI that uses command line instructions to flash PCBs....
Hello,
I'm currently developing on an NRF82832, I'm using a Black Magic Debug Probe to flash the firmware and the bootloader. I use Linux.
I have a working firmware...
Hi,
I started using nRF Connect SDK in VS Code recently. Everything works well, start a new Application, configure a new board, build, and flash.
While I found "Go to...
Hi,
I'm working on modifying the secure bootloader (SDK 17, nRF52840, s140) to store the old app before the new app is programmed into Bank 0 (see this other thread )...
Hi,
We have a design for a battery powered tag using a nrf52833-QIAA. I saw in a post from a couple years ago that you widened the DCCH inductor tolerance to +-20%. I...
Hello ,
I am trying to use NFC pin p0.10 as WAKE up pin , using nrf_gpio_cfg_sense_input(Btn, NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW); this code. I have defined CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I double-checked that when NordicUpdate_is_update_mode() returned false, I can still use the iOS Device Manager App to perform DFU.
I thought users needed to press...
Dear Nordic support Team
I have a question regarding the performance/specification of the RF front end of the NRF52 series chips. I noticed that the question "Is there an...
Hi, I'm testing the current consumption on a nRF52810.
I use PPKII to measure the current that the chip draws.
The software does the following.
Wakes up every 1 second...
