hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi guys,
I am using nRF5 SDK for Mesh v4.2.0 and I implemented this simple message model which can enable the communication between LPN and server node. After my nodes are...
Hi everyone, I see in nRF5 SDK 16.0.0, a Button/Led/Timer assign for handler, like that: bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler); Or: app_timer_create...
Hello,
I was working on buttonless dfu feature. I add buttonless dfu service as shown as ble_app_buttonless_dfu example and i manage to perform a ota dfu on nrf52 devkit...
Dear Sir.
Moving to version 2.4.99 from version 1.2.0 .
In previous version SPI worked well , cs was configured in overlay as
&spi3 { status = "okay"; compatible...
Hi,
I was evaluating FOTA on nRF5340 as possible upgrade to 52 series. All went good which I'm happy of.
However application size is limited roughly to half flash size...
Dear Community;
We are trying to send data via Lora using a nRF9160. The Lora transreceiver we are using is a RFM95W(Semtech SX1272). There are samples of code to receive...
Hi all,
I'm trying to set up my nRF52840 Dongle as a BLE Sniffer. I've followed the setup instructions from "nRF Sniffer for Bluetooth LE-- User Guide" v3.2, and I'm using...
Hi DevZone Team,
Is there a way to stop the ZigBee network steering after a device has successfully joined instead of waiting for the timeout to expire?
Thanks
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
Dear Nordic Technical Support Team,
I am developing a Mesh consisting of a client requesting to a net (group) of server nodes some motion data (which triggers automatically...
