Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hello all,
I’ve already looked in the following files:
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr\bluetooth\mesh\ access .h
C:\ncs\v3 .1 .0 \zephyr\ include \zephyr...
VS Code extension updated to 2025.8.654. Now when I click flash it says
And sits there spinning. Running west flash manually works.
Extension Features > Runtime status...
Hi all,
Im testing the "periodic_advertising_example" but in wireshark (nrf52840 dongle) I can just receive the AUX_ADV_IND packet below. I can I see the periodic advertising...
Application: Matter product using nRF54L15, SDK 3.0.0
Ecosystem: Matter product joins Apple HomePod
I am not able to get time/date delivered via Matter to the product...
What are the implications of doing this in one of the Kconfig files in one of my modules? should this override the first configuration of NFCT_IRQ_PRIORITY? from my undersanding...
I’m working on DFU using the BLE Mesh distributor and target sample codes. I built both with Sysbuild and flashed them onto two separate nRF52840 boards. The target board...
Hai,
We are developing a product having nrf54l05. I'm using nrf connect sdk for programming. I'm using one GPIOs for input. I have enabled pullup for that pin. We want to...
1. development environment:
software ncs3.0.1 , DW3xxx_XR6.0C_24Feb2022, vscode
hardware: nrf52840, DW3210
DW3210 is a UWB chip produced by Qorvo, and its corresponding...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
hi support team,
i have close this ticket:
but i need open this ticket and ask how to program 9151 externa; spi flash.
i don't know if 9151 json file is correct and...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
