I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Dear Sir,
Moving to zephyr new installation 1.4.99
Configure SPI1,SPI3 . I can see the SPI configured in zephyr.dts
spi3: spi@b000 { #address-cells = < 0x1 >; #size...
Hi,
I am using the stts751 temp sensor with nrf52832 for temp data logging for short time. I want to save temp data in the internal flash memory but I didn't find any similar...
I followed the instructions in https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.3.0%2Fsdk_config.html
and pasted the appropriate text...
Hello,
I have been trying to get the ADC working but for some reason, the adc_read function throws an error of invalid argument ( -EINVAL (-22) ). The adc_channel_setup...
Hi all, I have tried to follow the step to get up and running with my new nRF9160-DK, however, I am not sure if the Application FW has been successfully updated (how would...
Hi,
We are using a bootloader/DFU based on the secure_bootloader example with USB transport from SDK15 and It works fine.
Now, we are trying to add the possibility to...
hi.
i use nrf52840 to d evelop a keyboard .i connect and be bonded by a pc,now i want to delect to the bond info of the pc,and after this ,my adv cant be scan by this pc...
Hi Nordic Tech Support team,
One of my customers is having some problem with UARTE implementation. They used the ble_app_uart example ( pca10056 with SoftDevice 113 )...
Hello Everyone,
We are developing one custom device using open thread protocol.
We are using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 and Dev-kit - nRF52840...
IN Establishing the friendship,I received the following error
/** The Low Power node was not able to send transport command due to internal fault. */ NRF_MESH_EVT_FRIENDSHIP_TERMINATED_REASON_INTERNAL_TX_FAILED...
I want to send ADC data over bluetooth. When I searched, I found the following contents.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fble_data_throughput...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hello, I lived in Taiwan and I followed nRF9160 DK Getting Started and met a problem at establishing connection with nRF Cloud with my board.
The previous steps are all...
Hello, I'm trying to run C++ code on the nrf52832 but I'm getting an Hard Fault when sending a floating point to an ostream, like in "std::cout << 13.5f;". The FPU is enabled...
