Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I'm using the ble_app_uart as my template for Bluetooth and UART communication. I'm on SDK 15.3.0, Segger Embedded Studio and nRF52840.
I would like to send the information...
Hello,
We are facing an issue where we are having a lot of packet loss (UART nrf52832) on two sensors connected to an Android Application (Android Pie 9.0). The tablet model...
Hi!
I'm trying to implement a traditional ring buffer with the nrf_ringbuf library. I'm using nRF52840 DK with SDK 15.3.0 and SES.
I'm going to receive strings of data...
Hi all,
I am working with Thread SDK v3.1.
When I run mqttsn-client-public and subcribe to make MQTT-SN network use UDP. But it doesn't have DLTS.
In the topic : https...
Initiated west init as per nRF Connect v3.0.0 Getting Started Assistant but resulted into an error. Worked the last time I did this. Any idea what's going on? "west init ...
Hi,
I'm trying upload firmware onto the nRF24LU1+ dongle (nrf2728) from the nrfgo motherboard (nrf6310) through nrfgo studios. I have it hooked up just as described in the...
Hi,
With my mistake, the firmware in nrf52840 Dongle is none, Do you know how to get the official firmware? and how to download this firmware? if using Jlink, any pin support...
Hi All,
I have a scanner project based on nrf52840 + S140 and I saw S140 (7.0.0) seems to support nrf52811.
So I want to port existing project to nrf52811 + S140 7.0.0...
Hi, I am experiencing the nrf52832 with some testing and developing few examples.
I am using nrf5_SDK_15.3 SES. OS : Windows 10.
I am using nRF52832 only. I have seen...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
