Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
When static authentication is used, it is my understanding that both the provisioner and the privisionee have a static preprogrammed key. The SDK says:
"The application...
Hi, starting from the demos on the devboard, I want to make a custom pcb work now. For that, I do not need UART/logging functions, which will otherwise cost me current consumption...
I use SDK15 and S132. I have examples\dfu\secure_bootloader\pca10040_ble loaded in my board. I can see it advertising when there is not valid app loaded.
Also, my app with...
Hello Nordic Team
I am working on zigBee project. I see there is uart example available in SDK which works BLE + end point. Is there any example available which works on...
Hi all!
I found solution for Xiaomi zigbee smart home sensors (gerkon, water sensor, pir motion, and other...) based on CC2530 zigbee shepherd and Trust Center Link Key...
I am doing a project with nRF24L01+ but i found out this is not certified chip to FCC. Is any other RF that is certified that i can replaced this RF24?
Hello,
I am creating a read-only characteristic with sd_ble_gatts_characteristic_add (specifically, characteristic_add). The value is 31 bytes.
On a Read Request, it is...
Hello
I would like to send my sensor data to a mobile application using BLE SDK 15. Someone suggested me to go through the BLE NUS SERVICE example which was a good one....
Hi,
I am new to Nordic development environment.
I am compiling the some code developed by vendor for NRF5 SDK 12.2.0
I am getting errors such as
Error1 snippet
...
Dear Colleagues,
I could use some help or ideas. I’m working on the link layer encryption of an open source Bluetooth stack. It starts to work! But, now I have the effect...
Using softdevice 6.1.0 and SDK 15.2:
Is it safe to use NRF_UICR->CUSTOMER[0] through CUSTOMER[5] for storing serial numbers?
It seems through in previous versions of SDK...
Hi All,
I have implemented the code for MASTER serial DFU in ST micro controller. which can send the app .bin file. I'm using 57600 baud and disable the flow control....
Hello,
I am using 15.2.0 SDK and 3.1.0 Mesh SDK.
I was trying to control two LED's on the nRF52DK using two generic level server models. I made following changes to the...
Hello. I got an nRF9160 DK with an iBasis eSIM that was already registered on an nRF Cloud account. Is it possible move the already activated eSIM to my Cloud account? I tried...
