Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I tried to set up the ANCS example. It works fine. But how is it possible to set a higher MTU. I set the NRF_BLE_GATT_MAX_MTU_SIZE to 247. But the Log says after a connect...
Hello, somebody help please.. I want to implement Machine Learning using tensorflow, KNN or whatever is good for my module, that consist of Bluetooth Low Energy nRF51822 type...
I want to start with the following nRF52 ADC example .
While doing so, I found that the example is built on SDK v13 and SDK v13 doesn't have Seggar Embedded Studio support...
Hi
I successfully merged SDK for mesh v1.0.0 to nRF14.2 by following the example in https://devzone.nordicsemi.com/f/nordic-q-a/28936/merging-sdk-14-2-with-mesh_sdk .
...
nrf52832
SDK 14.2
My application is locking up, and finding the cause is proving to be difficult. I've enabled DEBUG and DEBUG_NRF and included the hardfault library...
I have an application that requires talking to 21 sensors wirelessly. The bandwidth required by each sensor is relatively small - roughly 2KB/sec. The sensors need to talk...
Hello,
The mesh lightswitch on/off example only calls 'sd_app_evt_wait' in the main loop.
I'd like to use '__WFI' instead. (Im combining some code with mesh, and i'd like...
Hello,
This case is a part of a private case. Unfortunately havent responded for few days. I believe he has days off or something, therefore I am willing to receive help...
Hi everyone,
I design own boar with nRF52810 SoC. But i dont know how to programming external. Which pins are using programming? SWDIO and SWCLK pins using programin i know...
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Written a custom script to write product model no into UICR Registers. After updating Model No, DFU was getting failed at state 6 i.e after updating init data after moving...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
I am trying to sent multiple messages from nrf52dk but it seems that i can sent only 7 even if i put a delay between messages . Any suggestions ?
for(int x =0;x < numberofevents;x...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
