hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Just received my Nordic nRF Smart Beacon Kit and was following the instructions in the User Guide to get setup. I inserted the battery into the beacon and there's an LED flashing...
My project is working but nRF connect does not seem to show it properly when advertising. It shows up for a moment then dissappears then shows up a while later on the RSSI...
I did try to SPI example in nRF5_SDK_11.0.0
But, I saw print in serial terminal only one-byte log which is NRF_LOG macro.
Basically, It SPI example included app_uart.c in...
Can't transmit a modulated carrier for FCC testing
part: nRF52832
We are writing our own firmware to support FCC testing. We have been successful at controlling the chip...
Our project use 51822 and another MCU stm32 to transmit heart rate data by uart. then 51822 SPP heart rate to smart phone APP. Now, We meet a issue that 51822 UART will crash...
Hi,
I just found what looks like a bug in ble_nus.c in SDK12 - not sure how to report it so I'm just doing it as a question/answer combo.
Basically:
Connect to...
Hi,
I'm developed a custom nRF52 board, and the main method to reset is via power cycling the power source (battery). Using GCC, should I still keep:
CFLAGS += -DCONFIG_GPIO_AS_PINRESET...
Now, I'm using the SDK12.1.0 and the device is NRF52832, I trying to use the secure DFU bootloader, when I open the Project Nordic provided(PCA10040 Debug) and build it, the...
Hello,
I have a PCA10028 that I want to use as a sniffer using the NRF Sniffer firmware. I tested it in macOS and it's working. The problem is that I also want to connect...
I put my code before ble_stack_init()
reset_reason = NRF_POWER->RESETREAS;
NRF_LOG_PRINTF("reset_reason: 0x%08x.\n",reset_reason );
//NRF_POWER->RESETREAS = 0xffffffff;...
Is it possible to receive connections without setting up a GATT service
For security reasons, I would prefer if generic apps and also the new Web BLE API could make connections...
Hi,
I loaded the code available at github for system on wakeup on gpio current and measured the current in low power mode by connecting a multimeter to a nrf51 dk.
The...
hi,
I am working with nrf51822 board using softdevice(s130).I am making ble initialization and continuously calling the power_manage() function in which sd_app_evt_wait(...
Before post this question. I post the MY QUESTION in stackoverflow forum.
but I couldn't find solution.
I know that Nordic board set Bluetooth Low Energy(BLE) multiple...
hi everyone.
we designed a custom board for nrf 51822QFAA chip and we flash the chip by using nrf51 DK debugger with tag-connect cable. when i flash the chip(using keil...
