hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
In a previous version of my project, that did NOT utilize TrustedZone, I was using a persistent storage library (NVS) and noticed that adding/using it would increase the current...
Hello,
I am developing an NFC application using the nRF Connect SDK v2.6.0 and the nRF Toolchain v2.7.0. During development, I tested my application on the nRF52840 DevKit...
I have MCU boot running successfully in my project using NCS 2.8.0 and sysbuild. I'm now trying to add hardware downgrade protection as described here:
https://docs.nordicsemi...
Continue.
PCA100059,S140,custermize periphral Blinky.
I have changed the value transfered between peripheral & center with
uint8_t* data;
uint16_t dataLen;
The max...
Hi,
I'm trying to use device_credentials_installer.py with an FTDI USB-UART cable, but the script returns "No device found." I've tested other scripts and confirmed communication...
Hello everyone,
I'm pretty new with BLE configurations. I'm currently implementing a BLE NUS service, and noticed that on the example code the max length supported is...
Hi Nordic Team and Other,
We are evaluating an audio product using a NRF5340 Audio Dk (Custom Board) and using nrf5340 DK for flashing the custom board using the setup as...
Hi,
We have a pcap file of a MQTTS connection to AWS, provided by the Soracom SIM console. I will print the first lines of the Wireshark trace so you can see what I am working...
Hi, We are evaluating whether nr54L15 supports LE Audio function? According to the specification, it supports bluetooth 6.0 and should support LE Audio (Isochronous channel...
Hi,
currently I am struggeling to get my SD card connected to the 54H20 DK. Each time I try to mount the SD Card I get the following error:
The Error is raised after the...
We are using a custom board design. I created a custom board configuration when using the v2.5 SDK. In this configuration, we have the UART0 pins configured such that RXD...
Hi
I want to use the timer in counter mode (gpio event shortcut to count task). Do you have any number of current consumption? The plan is to have a 64Hz signal but it could...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
