According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
i have to use mqtt for my project. Now am using nrf 52840 for transfer data to from my device bt840 if i want to go with MQTT have to connect wifi module with ble.
esp32...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating NUS Central...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating CDC ACM...
I'm using version 2.0.0 of the Android version of the device manager app. When I select my device from the list to do a DFU it immediately closes the app. Normally it would...
sometimes the param update will fail and sometimes will not. May I know what the reason is and how to solve this issue?
error case;
normal case:
my prj.conf...
Below are power consumption measurements of a DUT being booted with the same PPK2 in SMU mode with various software versions. The only variable being changed is the PPK2 software...
Hello all,
I want to use nrf52840dongle to receive notifications from other BLE board.
I have tested with nRF Connect for Desktop Bluetooth Low Energy successfully.
...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK.
I didn't change anything in the sample code but only modifying the NRF5340_AUDIO_TRANSPORT_MODE...
Hi there,
I generated the DAC, PAI, and PAA certificates using the chip-tool and merged them into my firmware as factory data. Additionally, I generated the Certificate...
conducted an ADC experiment using the nRF5 DK (PCA10056).
The power supply for the nRF5 was provided via USB.
Based on the SAADC sample, I coded the following:
...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
Hello,
I want to operate a rather complex spi sensor with the nrf5340. To do that, I wanted to first establish spi communication. I started by creating a hello world example...
My name is Cedric, responsible for Workplace Management at ´my company, which also includes application management. We try to install all of our apps centrally via Intune...
