Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
We have power ceilings configured as per the last nRF7002 Product Notice :
Yet we are seeing values below expected (around 13 dbm):
We noticed upgrading to 2.7.0...
Hello, and thanks for reading. We are having some problems with our device, and hope someone here has the missing piece of wisdom we need. Our device implements HID over GATT...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...
Hi,
My custom board uses Raytac MDBT53v, which has nRF5340 as its MCU.
My SW is based on the example audio code, and I want to use my external NOR FLAH IC (Macronix MX25R6435F...
Good day,
I am trying to combine gzll, USBD HID and USBD CLI with SDK 17.1.0 and nrf 52840. GZLL receiving input, send to USBD HID, USBD CLI output logs and debugs.
Below...
Hello,
I am finishing the development of a device based on the nrf52810. When the device is connected to a central, I would like to periodically measure the voltage on VDD...
Hello, we have application based on ncs v2.7.0. We use cmakepreset and cmake for building application. We want to add DFU functionality to our project. We study following...
I used ncs sdk 17.0,when i build project,it will occur No board named 'nrf54h20dk_nrf54h20_cpuapp' found.
could you give me some help please? Thanks very much
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
Hi everyone,
I'm currently working on a project involving an Ember ZigBee end device and a Nordic ZigBee coordinator ( Nordic nRF52840 donngle) . I’ve encountered an issue...
I am not being able to set up the modem in Pakistan. We bought the board in Canada and we've tested it out in Canada without any issues. But the same Soracom sim card is not...
Hi,
I am writing a app.overwrite to remap my pins table. I can use
/delete-node/
The above is no problem. Bu my pio is overlay with gpio1 pin 5. The original dts...
I am using nrf52840 and have two questions regarding flash memory.
1. If the write erase cycles limit is reached for certain page of the flash, only that page is going...