Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I am creating a Matter accessory device with the nrf52840dk and the guide on https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
Is it possible to build an asset tracker on the nRF91 without the use of LTE-M or NB-IoT? If there is a solution, could someone please advise. I read something about GNSS...
Hello,
SDK : nRF5_SDK_17.1.0_ddde560
Example: ble_app_uart
I want to use custom peripheral and disable BSP.
but when comment buttons_leds_init(&erase_bonds);
I...
I'm using nRF Connect SDK with nRF52840dk and going through the UART samples and currently have both the P olling and Async methods working to some extent. But questions for...
Triggering advertising by button pressed. But when advertising state is not idle. Both sd_ble_gap_adv_set_configure() and ble_advertising_start() failed with errCode 0x8....
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I am using a function in my source code that reads the current RSSI of the connection. The function, read_conn_rssi...
Hi there,
I am trying to implement the OTA DFU feature via Zigbee in my product. i tried to implement the example available in SDK as below https://infocenter.nordicsemi...
We are able to build nrf5340_audio application with SBC codec,
but error occurs when program the app core with buildprog.py
dongtaotao@dongtaotao-OptiPlex-5070:~/ncs_v2...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Greetings,
In our product, we encountered an issue when data saved in flash (FDS) that were previously retained are erased during DFU on some devices . This was indeed fixed...
Hi, I'm building an applicaiton based on ble_app_uart. I got that using idle_state_handle(); function to set the my nRF52833 into system ON mode. I disable system OFF mode...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
