Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi there,
We are trying to enable the interrupts on one of the UARTE peripherals, and are having trouble finding the interrupt number within nrf5340_application.h? It is...
Hi Everyone,
The custom device I am working on is a BLE peripheral device and uses softdevice S132,
therefore to get accurate triggering of ADC sampling and to avoid periodic...
Dears,
We are MCU Programmer Supplier, now we are developing the off-Line Programmer for NRF5340, and encounter some problem as below:
1. Does the Nrf5340 Flash Memory...
I have a custom model server that sends 8 bytes of data
I set up 2 nodes - one to publish to an address 0xC002, one to subscribe to publication
Provisioning and publish...
Is there any documentation/tutorials for using NRFX drivers directly in Zephyr without trying to create conforming device drivers? I have a lot of code written for the NRF52840...
We have a board based on the nrf9160dk.
The project is essentially based off the "LTE sensor gateway" project with hcl_lpuart to utilize the nrf52840 for BLE. Chip shortages...
Hello,
I am performing garbage collection. During the garbage collection an event could be fired (from the softdevice) that causes updating of records.
My question is...
Hi
I would like to know, if Zephyr-s ssd16xx driver supports display driver board power supply control? I see from Zephyr documentation ( solomon,ssd16xxfb (on spi bus)...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
