Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
Hello,
I want to make sensor sleep and wake-up according to VDD.
- When VDD is below 2.8V, Sensor sleep.
- When VDD is above 2.8V, Sensor wake-up.
Since my board...
Hello,
We have a question from one of our customers as to whether the 52833 is compatible with the S340 Soft Device. On the Nordic website, it is not listed as a compatible...
Could someone explain how to power the nRF52840 via USB?
Looking at the schematics, and also reading the "objective" spec, I can see that VBUS is connected to the USB input...
Hello,
Since yesterday's update of the nRF connect extension the device name of the target in the "connected" devices screen is updated from nrf9160_xxAA to nrf9160_xxAA_REV2...
Hi Everyone,
I tried to build lpUart example from samples available. I was trying to debug then I got the breakpoint on
"__ASSERT (lpuart, "Failed to get the device...
i was working on nRF52840 and nRF9160 with NCS v1.8.0.
i'd like to find an API to reboot system. so i tried to call NVIC_SystemReset(). it works in my nRF9160 project. ...
I am currently designing a PCB which incorporates the nRF9160, and I would like to know the devices behaviour in between 2.0 V and 3.0 V, as this is below the minimum VDD...
Dear,
We are working on our custom boards to develop a watch product which need external flash memory connected by QSPI interface. In this product, the UI images and font...
As I learnt, nRF5232 defaut with LDO mode, DC/DC is diabled, but I can not find any config in nRF5 SDK for nRF52 DK,
someone said to use: sd_power_dcdc_mode_set,other said...
Hi,
I've been reading that the nrf9160 can only receive up to ~2KB of data at a time. It seems that the connection terminates if I send too much to the nrf9160. I tried...
Hi again Nordic, I need some pointers. Håkon, a very patient man here, sent me an example code repo of usage of external flash memory on the nRF9160DK. I've tried the sample...
