Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
Hi,
Currently I am experiencing some issues regarding flashing the modem firmware on the NRF9160. My end goal is to automate the process of flashing both modem firmware...
I am using SDK v12.3.0 for nrf 51822 chip. I am working on hrs example with some custom modifications, so i need to to update application through OTA, i have used bootloader...
Heija Guys,
I have a problem with my PWM. I started with the zephyr version 2.4.99 and switched, after we discovered a bug (Link to ticket: https://devzone.nordicsemi.com...
Good Afternoon, Im using a samsung galaxy tab a - Model num SM-T510 Android Version 10 nRF Mesh app version - 3.1.5
After provisioning 14 nodes, whenever i try to reset...
Hi,
I am trying to integrate UART and DFU serial from the mesh example.
What I did is:
1. Adding uart drivers and libraries into the DFU project.
2. Adding codes...
Hi,
We are seeing the issue mentioned in https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in-saadc-samples-with-easy-dma-and-ble/79053#79053 . We have 2 sensors...
Hello, I'm getting started with FreeRTOS in Nordic SDK 15.3 I have created a small test code, using binary Semaphore from FreeRTOS, that waits signal from SAADC callback....
Hi, I want to do some modification in the existing nrf connect sdk sample projects. I did some modification in prj.conf and CMakeLists.txt file. But now I am not able to load...
Hello,
Could please someone suggest to me the 10 POS debugging header(5*2) with 1.27mm with a lesser size footprint?
I need a lesser pad size so I could place it on my...
