I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I want to run a memory test whenever my device nrf52832 starts up to check for various faults like stuck at, transition and other faults in both flash and RAM. Does...
Hi All !
Hope doing well . I have a question regarding nrf52833 maximum power transfer @ 8dbm . I am using the "ble_beacon app" and using sdk 17.2.0 and soft device is S140...
Hi. I am working on the nrf9160. I want to use a unit test framework for my application code (which is a combination of C/C++14). I thought about using gtest/gmock or ztest...
I'm using NCS V1.5.0 and an nRF52840
The current draw with I2C enabled is around 200 micro amps
If I disable I2C using an overlay and recompile the current draw is around...
Hi all,
Please forgive the newbie question--I'm just getting started with Nordic.
I'm trying to build the hex files for the pc-ble-driver and the build keeps failing....
I am trying to add the nRF SDK 15.3.0 ILI9341 LCD driver code to my existing nRF52840 project.
Segger Embedded Studio 5.40a is being used as the IDE.
I have added all...
Hi,
I am new to Nordic chip sets, though I have firmware experience with STM and other boards. I have to wire an accelerometer to a nRF development board, and fix some existent...
Hello I am fairly new to Nordic. I am able to send and receive a character only but not able to send a string.
I am trying to send a character via RS232 to Tera Term using...
Hello,
I would like to print signed long long int (s64_t ) values using printk or printf.
I tried some suggestions I found online %lli , %lld but they did not work.
...
To the kind attention of Nordic support team,
I'm using nRF52833 and activated wdt with multiple reload registers enabled. I'd like to get an idea about which one of those...
Dear Members,
I run the software for detecting HRM and BSC for 80 minutes,
but I got only speed and cadence, all the interrupts from HRM are gone ,
is it related with...
After having development success with the nRF52840 I'm beginning to look at development on the newer nRF5340. I've successfully gotten the blinky example working on the development...
hi, i am working on nrf52 mesh examples. all example are compiled properly but ble_app_uart_coexist example in sdk_coexist folder is not compiling. there is "nrf_log_backend_rtt...
I appear to have some very simple code that when loaded into a nRF52840 kills it, such that I cannot recover it, possibly hardware failure. I would appreciate any suggestions...
Hi
According to the product specification, the power fail comparator nRF52832 has a threshold tolerance of at most +/-5%. When I configure the power level warning to 1.7V...
