Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi!
I'm using nrf sdk v1.3.0, for power saving, i'm have to activate and deactivate lte, after a few time activate, send http request, get data and deactivate lte, the modem...
I am working on design of low power BLE sensor based on nRF52. Sensor data is included within advertising packets, in manufacturers data field. I would like to detect event...
I have troble when try to change custom service to Environment Sensing Service in this sample
https://github.com/maidenone/custom_ble_service_example
I used the sample...
Cheers!
I've been working to enable TWI0 for our current project, but I've been getting stuck on this compile error:
../SDK/modules/nrfx/drivers/include/nrfx_twi.h:73...
Hi i tested the code with nrf52DK with same code getting 3 analog value from AIN1, AIN2, AIN3 and it worked fine.
But when I use EYSHSNZWZ for my pcb, ADC value was just...
Hi,
On battery powered devices, how is it possible to retain a root key when changing batteries?
The crypto cell has an Always On power domain for retaining device secrets...
Hi guys,
I'm currently using SDK 15.0.0 in Keil MDK and making use of the new NRFX drivers.
Similar to the issue detailed here: https://devzone.nordicsemi.com/f/nordic...
Hi,
In the documentation , you have specified that the nRF Toolbox is supported for mcumgr FOTA.
However, from our tests, it seems that it is not true. Could you please...
Hi,
I'm experimenting with the lwm2m sample on the nRF9160-DK and I enabled the firmware update pull support through a COAP to HTTP proxy :
then simply added :
and the...
Hello peer developers,
This is a general question and dilemma I am dealing with and I wanted to get your opinion.
I am working on a project to implement a short range...
Hi,
Here, i have using two I2C functions EEPROM + SENSOR with nRF52832.
Initially, using ble_app_uart example to read Sensor data using TWIM.
Every minute read Sensor...
I started with ncs/nrf/samples/nrf9160/lte_ble_gateway and have taken parts of ncs/zephyr/samples/subsys/fs/fat_fs to get SD card support
prj.conf
CONFIG_NEWLIB_LIBC...
Here are some of the issues which I am facing in SEGGER Embedded Studio since I updated to nRF Connect SDK v1.3.0:
After I press Debug, Go, a dialogue box opens asking...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
