Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
On nRF52840, we are able to engage APPROTECT by setting NRF_UICR-> APPROTECT to 0. However, writing 0xFF to NRF_UICR-> APPROTECT does not seem to disengage APPROTECT...
If you call nrf_serial_write() once to transmit some data, and before the data from this first call is transmitted, you call nrf_serial_write() again, will the NRF_SERIAL_EVENT_TX_DONE...
Hi Team
I would like to know are there any pic libraries for nrf24l01?
Need to send and receive data from PIC16F1526 to an other PIC MUC via nrf24l01 transceivers.
...
Hi,
My task is to work on NFC , I know the basic working principle of NFC . Here I have seen the nfc uart example .
I would like to transmit the device name, mac address...
Need advice on choice of advertisement flags.
Beacon advertises alert and non alert beacons: On the alert beacons the central is required to connect and respond to the beaconing...
I have looked at and used the following references:
https://devzone.nordicsemi.com/f/nordic-q-a/47484/ble_gap_evt_scan_req_report-not-working
https://devzone.nordicsemi...
Is it possible to implement open thread cli using 16 castellated pins of BT840 ?? I can change the uart pin by rebuilding the open thread libraries ,
Can I avoid using...
Dear all,
In our project we are using "nrf52840" IC is used. We need to check its strength in various physical layer by loading the " Direct mode code ".
We have sucessfully...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
To the kind attention of Nordic support team,
Could you please help me finding documentation about the subject I mentioned?
Let's suppose we have got a peripheral and...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
