hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello,
I am searching the way of decoding the motion raw data from thingy 52.
Especially, for the accelerometer values.
In the app, I get the next value:
FAFF...
I read the post here. This post was used nRF52 DK (PCA10040) . I have the nRF52 DK (PCA10056) card. nfc applications in sdk always nRF52 DK (PCA10040). How do I run nfc applications...
Hi,
This error occurs when I write below command for OTA_DFU demo:
cmd : exe keys generate private.key Error:
ImportError: cannot import name 'DIGCF_PRESENT' from...
Hey,
I am working on mesh program, I am trying to send mesh message periodically for every 5 secs when i press a button in nRf52 DK. The message is being send for 3 or 4...
Hi,
I am using nrf52840 module with a kit that i built by myself. The kit is working because i am able to flash and debug without problems.
I am using Segger embedded...
Hi,
Is it possible to advertize and scan only on the 2M PHY and w/o using at all the 1M PHY on nRF52840/S140 system ?
The actual system is running fine if we use the 1M...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Sorry in advance if this is an FAQ or maybe two
Situation is this - for regulatory reasons, production/release software here is built using a known version of arm-gcc, and...
I'm using scannig with whitelist on nRF52840 Dongle SDK V15.2 (usbd_ble_uart_freertos example)
when BLE_GAP_EVT_ADV_REPORT is called scanning stops, So it can scan just...
I am working on matching an antenna to the nrf52832 QFN package. I am looking at the reference design, which has a 30 mil wide trace. I believe that is supposed to be 50 ohms...
I have an application (key fob) that needs to wake up on a button press. Scan and connect to a specific BLE device, then send one byte of data and disconnect and turn off...
Hello, I have a question about using PPI with a SPI transfer.
I’m using a NRF52832 custom board with the Softdevice. I’m reading sensor data every 20ms via TWI and sampling...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Hi,
I use the server and client from "light_switch DEMO", along with iOS app (nRF Mesh) for setting and pairing. Both ”subscription” & ”publish address” are set as 0xC001...
