Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I'm trying to get a Bluetooth interface (Bluefruit) to the Nordic BLE softdevice under NuttX. Right now it's very unstable. It will work occasionally for 90 seconds and then...
Hello,
When trying to connect to our custom board, it ends in Time out after 5 seconds.
On the board, I put the simple Nordic_Blinky example (\examples\ble_peripheral...
For the custom_ble_service_example , trying to change the service used in the example to a Bluetooth SIG service.
Original is: CUSTOM_SERVICE_UUID_BASE f364adc9-b000-4042...
Quick question: when will the nRF52840 DK available? On the nRF52840 DK page, there is a recommendation to avoid the PDK:
"The nRF52840 replaces the nRF52840 PDK which is...
I have the super typical problem of needing long data transfer greater than the 20 byte MTU size.
I have a basic protocol that has the total length of a long message coming...
Hello everyone, I am very new to nRF52832 Development Kit and was testing some examples to get familiar with this kit, however i encountered an issue while testing the ble_app_uart...
Hello,
We are having problems with Gazell pairing. Both the host and the device are using the Gazell stack from the nRFgo SDK 2.3.0.10040 ported to run on an Atmel SAMD20J18...
sdk 15.0, SES
In CMSIS checked NRFX_TWI_ENABLED, and checked and unchecked TWI_ENABLED to no avail.
Looked at driver API , but with no specific hint.
Looked for other...
Hi Engineers !
We are going to implement AES CRYPT/DECRYPT Protocol over BLE to add some additional protection against HACKing with use of HW " 6.6 CRYPTOCELL" the MODULE...
Hi, I want to use a couple of 0805 resistors, hook them up in tandem to 220V AC power source, and then do some zero-crossing detection.
I know I know, this totally isn't...
Is it possible to use the Segger SystemView software with the NRF52832? When attempting to use SystemView, I get an error "RTT Control Block not found". It's possible to enter...
Hi,
I can't find information what shape of spectrum I should expect from test mode (CONT_WAVE = 1, PLL_LOCK = 1). At the moment I get main spike with smaller symmetrical...
I'm running into an issue when trying to use the timeslot API for advertising while concurrently scanning. Scanning is using a 100 ms interval with 50 ms window and initialized...
Hi!
I have created a project for nRF52 DK in Segger Embedded Stuido. I wanted to creat it for nRF51 but there was no eamples to start from in the sdk that supports pca10030...
