Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Dear Nordic:
Light bulb project support 52840DK, can light bulb project support 52840 dongle? I have not found dongle option in l ight bulb boards folder, only find nrf52840dk_nrf52840...
Hello. consisting of nrf7002 + nrf5340, I'm going to do battery management and power management of a circuit that operates up to a small coin electric motor at npm1100, and...
Hi,
I am encountering an issue with the BLE connection on my nRF5340 DK. When I attempt to connect the device to my PC, the pairing process takes a significant amount of...
Hi,
I am implementing a BLE central that is based on ble_app_uart example using nRF52833 with a soft device version 7.2.0.
I have noticed that a single packet download...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I am trying to enable the watchdog in my application, and I can successfully locate the device node and add a timeout, but...
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
I am simply trying to build the hello world (and blinky, results are the same) with NRF-SDK 1.8.0 - it's based on Zephyr 2.7, which is the LTS release.
Target board is 5340...
Hi,
We are planning a new project that needs to use very low power. Since relay mode uses more power than simple node, can we turn off relay mode on all nodes until an event...
Hi, I am developing BLE beacon application on the nrf52820 soc which has limited Flash resources. I want to have the FOTA through BLE abilities built in to enable firmware...
Hi! Can you please help me identify what is causing this issue and/or provide more info about this:
[00:04:23.038,330] \033[1;31m<err> bt_sdc_hci_driver: SoftDevice Controller...
Hello everyone!
I'm working with the nRF52840 microcontroller and I wanted to get a bluetooth antenna and since I know that the whole RF thing is very complicated, I was...
Hi.
I have a custom board with a NRF9161. The nrf91's LTE block connects to the sim holder through a NX3DV2567HR switch and an TPD3F303DQDR ESD protection.
I'm using...
