Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I am getting this error on the 7th time I perform an action:
I understand it's an lvgl error and could be specific to lvgl but I think, considering it's only happening...
Hi,
first of all i know that this is not a "good question", but my hacker side is trying to... tweak hex file of softdevice 113 to fit my low memory footprint.
I mean...
Hello everyone, I am working on a custom board based on the nRF5340 and need to implement code execution from an external QSPI memory. The board uses the IS25LP128 memory...
Hi, I am working on a project that collects data from various sensors and transmits it to a Mobile application via BLE. Can I use Isochronous Streaming for it? Can I set up...
Hi community! I have custom boards using nRF5340. A couple boards has suddenly gone bad and unable to be flashed or communicated with after a few reflash cycles.
I've read...
Hello
I would like to sign an image temporarily with west CMake options as described in Enabling a bootloader chain using sysbuild using the comand line:
In it's final...
Dear DevZone:
I use NCS 2.8.0 to build Light Switch FW, my build command as below:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp...
Dear Devzone,
I currently use the nrfutil dfu serial command to upgrade the firmware, which is OK. I want to upgrade the firmware of 52832 through MCU, so I need to know...
Hello support,
We are developing a battery-operated sensor. For that, we are using nrf5340. Also, we made an enclosure for the sensor.
While developing we found that the...
Hi there,
Is switching between UART and I2C runtime on the nRF52840 with Zephyr possible when utilizing the same two pins for TX/RX vs SDA/SCL?
Thanks in advance,
L...
What version of LVGL is used with nRFConnect for VSC 2.7? Where can I find this information generally. It seems like the lvgl version is 8.3, but I don't know why I think...
Hello,
I am writing this thread to ask what would be the hardware configuration for the QKAA version of the nRF5340 chip if I don't want to use the wireless features of...
I am considering using the nRF7002 for a Wi-Fi application. I want to use an nRF54L15 as the host for an nRF7002 and operate it using Target Wake Time (TWT) to periodically...
I need to connect to other units according to their MAC address. I'm assuming that this:
BT_SCAN_FILTER_TYPE_ADDR
Is the thing to use in this:
bt_scan_filter_add...
