I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am developing a nrf5340 based device (no external memory) using FOTA to update the firmware. This process used to work quite well for a while now, but I ran into trouble...
Hello,
I am trying to use PWM to control two LEDS, one red and one green (referred to as blueled in the code) to produce different colours. I have had a look at the example...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I'm studying the CDC_ACM...
Dear support team,
We need to add custom fields to the node database (CDB), as shown in the screenshot below:
Use bt_mesh_cdb_node_store(); to store, and then use the...
Hello,
I installed NRF Connect SDK 2.6.1 on Ubuntu following this guide, Now I try to follow the tutorial for Adding clusters to Matter applications . I'm stuck at (2) Adding...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
Hi.
I am using SDK v2.6.0 (Toolchain v.2.6.0). When I open VS Code (v1.91.1) I keep getting this warning -->Bad CMake executable: “”. Check to make sure it is installed...
Hello, I am developing on a custom board with the nrf5340 and programming through SWD using the nrf5340dk. A few days ago everything was running fine and I was able to continuously...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
Hello Engineer Greeting of the day i am building my product using nrf52833 IC , there are some communication modules connected to the 52833 , i want to cheack lowest power...
i have to interface MT29F4G01ABAFDWB in zephyr rtos but i need help how create overlay file for it(i want to interface it using spi), i already have bare metal drivers for...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
When trying to flash the hello world program onto an Adafruit nRF52840 Feather through a j link it fails with "FATAL ERROR: one or more Python dependencies were missing; see...
