Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi, We have a device configured as a peripheral and want to provide the user with the peer device name typically connected to it, like the device name. Typically a phone will...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands(READ, WRITE, etc.) to the IntanRHD2132(ADC) at regular...
We have a sudden problem with the flash_manager. The code stops at static uint32_t flash_area_build(flash_manager_t * p_manager), at line NRF_MESH_ASSERT(p_manager->config...
Hi.
I am designing a 4 layer PCB (0.8mm thick) for an nRF52820 microcontroller.
My board's stack: L1 - Signal L2 - GND L3 - Power L4 - Signal
I have questions regarding...
Hi dear forumers,
I'm in the goal of achieving lowest current consumption on my PCA10056 DK board, with an nrf52840.
I converted a previous zephyr firmware who perfectly...
Hello, I am using the nRF5340 Audio DK with Zephyr and want to use I2S to send audio to an I2S device. So far I have had little success with the microcontroller halting in...
11 months ago in an answer a nordic member wrote (in regards to an error that I now also had and could solve using CONFIG_DEBUG=y):
[quote userid="81283" url="~/f/nordic...
Hi there,
I have an issue when using PPKII software on MacOS at 100ksps (no issue at 1K):
The 10min button at the top does not appear anymore
After a 3min measurement...
Good Afternoon,
I'm designing a 4-layer PCB based on an NRF52832 (QFAA) paired wit h a Molex 479480001 SMT Antenna, and I was hoping for some feedback on Antenna Matching...
Hello,
I'm trying to sniff packets with wireshark by varying the connection interval and supervision timeout of my ble application. I see that with lower connection intervals...
I'm presenting an issue when exporting the data collected, specifically the digital outputs, they are exporting incorrectly, but in the Data Logger tab they are presented...
When implementing AWS_IOT provisioning by claim process, AWS_IOT responds to the published topic $aws/certificates/create/json with a 3580 byte response. This causes TLS to...
Hey, I'm pretty new to Nordic Development. I am working on nRF5340 Audio DK development board right now and I was trying to create a bluetooth speaker kinda setup using the...
Regarding the design issues with the nRF5340, I have adopted the nrf5340_qkaa_config3 design scheme from the hardware design package. However, after testing, I found that...
