I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
Is there any existing support for an e-ink display interfacing with the nRF52840? Something that already has an existing LVGL driver and can be integrated with an nRF...
Hi team,
I'm currently facing an issue with the nRF52832 and nRF52833 gateways in our setup. Here are the details:
Current Configuration: - Scan Interval: 100ms - Scan...
Hello everyone,
I have developed a program that utilizes UART communication, Bluetooth Mesh, and TWI/I²C functionalities, all within the framework of the Zephyr project...
HI,
I am building an IoT product using NRF58233 ICs. In which I use 3 PWM channels and 3 ADC channels. You can review the principle I attached to make sure nothing went...
Hi,
I have a strange problem. I use a serial port timer to retrieve serial port data. When I compile with debug, the program runs normally, but when I compile with release...
Hi,
I am using nRF52840 DK and Bluetooth Observer example program. I am implementing filtering. I am having trouble add include scan.h which is located at C:\ncs\v2.4.2...
Hi Support Team,
I have an nRF7002 DK board and I am using SDK v2.6.0. I am facing an issue when sending data from the client to the server. Below are the steps taken: 1...
Dear colleagues,
with the newer SDK (I am now using NCS v2.5.0 and 2.6.0), I have difficulties finding the right SYSTEM OFF mode current. Code currently looks like as follows...
Hi
I use nRF7002 with SDK v2.52, try to connect external MCU and use uart call back function, to recieved and send bcak the recieved data, It will happen fatal error and...
Hi,
I have bunch of SEDs (sensors/clients) and one or more FTDs (hosts) working on CoAP protocol. SEDs send data packets once in a while and mostly sleeping. I have few...
Hi,
I'm testing the NCS direction-finding-connectionless demo,
NCS V2.6.0
this is my overlay:
and my ant_patterns:
According to the white paper and some other...
Please, I want to flash Zigbee Weather station App on thingy53, I faced two problems:
1- i can't find the board in build configuration.
2- i tried to use programmer and...
Team Nordic,
Question for you. In nRF5340 datasheet, page 1, Flash and RAM description : https://infocenter.nordicsemi.com/pdf/nRF5340_PS_v1.3.pdf
I found description...
Hi,
I am developping a non blocking TWI (I2C) communication, calling this function:
The init function of the twi is :
Please note that the real code is splitted...
I am having some issues with spurs when looking at the RF signal with a spectrum analyzer. The problem disappears when using __WFE() at the same time as sending constant carrier...
