Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
I'm integrating an external SPI flash W25Q32 with the nRF52840 using the NOR FLASH driver, but it's not functioning properly as the MCU log indicates an MPU error. ...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi All!
I have a question, i am using nrf52833Dk as an extended advertiser and nrf52840 dongle / 2nd nrf52833Dk as a scanner using the BLE desktop App (nrf connect for desktop...
I am not able to send 25 array packets each second. array size is 244 bytes I am reading the sensor data continuosly and every 40 ms i am sending the data to bluetooth using...
Hello,
I am on a development team utilizing Nordic Board NRF52DK to connect to a custom NRF52832-based board/external device via debug out on the Nordic Board NRF52DK, the...
Hi,
I'm experimenting with an Acconeer XM126 board which has an nRF52840 processor (and an Acconeer A121 chip) and a Bluetooth antenna (and an RF antenna too). I'm deploying...
Hi all.
I have made myself a board which has a module with the nRF52833 chip embedded onto it. It's effectively a board with a set of switching regulators on it to drive...
I am using NRF52833 and trying to setup DFU specifically for OTA.
As experienced in other threads the size limitations are there
Secure_Boot builds creating slot partitions...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hi,
I have an implementation in which two boards communicates through ble and i want to measure the throughput of both. The behaviour that I see is that increasing the connection...
Hi,
I have a Tuya FingerBot Plus and when using the Zigbee Shell sample:
1.I can 'click' the finger using a ZCL command
2. I can't change the 'finger mode' from 'click...
Hello
I have 2 devices ,a central and a peripheral on a custom nRF52840 board
Using Zephyr SDK 2.5.0
The distance between the devices is 10.9 meters. When TX power on...
Hello,
We have nRF52833 on the custom board, now we want to do DFU over Bluetooth. During my initial research reults with following questions:
If you use 1. " nRF Connect...
Hi, Everyone
I have space constraint in my round PCB for RF section where i have take referance from thingy91 board and choose the same components exept mcu is nrf5340 claa...
