I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi all,
I am evaluating ANT+ features in nRF52 DK board and I am using nRF5_SDK_17.1.0_ddde560 SDK.
I need to implement ANT+ Bicycle light profile (LGT) in my device....
Hi.
I'm developing a ble module now.
I have a question about time out, interval among BLE init Advertising.
As shown in the picture below, time out (in units of 10ms...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZED)
NCS v2.4.1
Hi,
I am working on Tunneling cluster handling as that one...
Development environment: ncs 2.6.0.
my application need BLE-DFU, so i added multi-image support to my project.
the pm_static.yml is the typical default system configuration...
Hello,
I am working on a SWD flasher for nRF52 chips. I try to perform basic commands like flashing a firmware or reading flash content. I wanted to use FICR informations...
I am using NCS V2.6.0 and using zephyr there is no examples to measure battery level using saadc we can measure the battery level right? I used LEDs to indicate battery level...
Hi, I'am working on a design with nRF7002 and I need add WiFi antenna NN03-320 from Ignion and when check the datasheet of the builder of the antenna I see that the pin 4...
Hi there,
Is there any drawback or limitation in the S140 SoftDevice (v7.3.0) if a connection (as master) stays open for a very long time (weeks)? I mean, there could be...
Hi,
I use our customer board that enable the i2s to the DAC to speaker. However, i only verify the play a wav file directly that seems work normally but our target is playing...
which sample is best for me to verify the central/peripheral communication using nRF52833 for nRF52 serial.
I have two nRF52833 DK board, I need the board2board communication...
use NRF52832 do a ble hid keyboard,
when do the keyboard function test need connect the keyboard to computer or laptop.
only when the connection it's done, then can run...
I used nRF52840 board with SDK 17_1_0 ,
For FCC Certificate We used Radio Test Example,
using start_channel 40 & start_tx_carrier we change the frequency and we are able...
I am using nrf52832, SDK17
When I am setting up a timer with no applicable interrupt handler it fails so
This is how initialize the timer
when I do define the handler...
Hello community,
I am trying to develop a custom bluetooth HCI_USB code for the BL5340PA BLE controller board. The Liard Connectivity's(now Ezurio) BL5340PA : https://www...
